M 2 6 8 1 S A M FUJITSU
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 3.5"/SLIMLINE Cylinders 2379| | |
Capacity form/unform 264/ MB Heads 3| | |
Seek time / track 14.0/ 4.0 ms Sector/track | | |
Controller SCSI2 SI/FAST Precompensation
Cache/Buffer 256 KB Landing Zone
Data transfer rate 3.000 MB/S int Bytes/Sector 512
10.000 MB/S ext SYNC
Recording method RLL 1/7 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 5 50 | -45 60
Power: sleep W Humidity % 20 80 | 5 95
standby W Altitude km -0.300 3.000| -0.300 12.000
idle W Shock g 5 | 50
seek W Rotation RPM 4500
read/write W Acoustic dBA 43
spin-up W ECC Bit
MTBF h 250000
Warranty Month
Lift/Lock/Park YES Certificates
**********************************************************************
L A Y O U T
**********************************************************************
FUJITSU M2681S/2682S/2684S JUMPER SETTING C141-E008-IM 1994
+---------------------------------------------------------+
| |XX I
| CNH2-+ RP1 |XX N
| | |+---+ |XX T
| ++++-+| | |XX E
| CN6-+ | | |XX R
| | | |XX F
| +---+ |XX A
| +--+ |XX C
| +--+ |XX E
| +-+CN5 |XX
| +-+ |XX
| |XX
| |XX
| +-CNH1 |XX
| | | |
| | | |XX POWER
| +-+ |XX
+---------------------------------------------------------+
**********************************************************************
J U M P E R S
**********************************************************************
FUJITSU M2681S/2682S/2684S JUMPER SETTING C141-E008-IM 1994
Jumper Setting
==============
x = Factory default
CNH1 SCSI ID
-------------
+----------+-----------------------+
| SCSI ID | Jumpers |
| | 5-6 | 3-4 | 1-2 |
+----------+-------+-------+-------+
|x 0 | OPEN | OPEN | OPEN |
| 1 | OPEN | OPEN | CLOSED|
| 2 | OPEN | CLOSED| OPEN |
| 3 | OPEN | CLOSED| CLOSED|
| 4 | CLOSED| OPEN | OPEN |
| 5 | CLOSED| OPEN | CLOSED|
| 6 | CLOSED| CLOSED| OPEN |
| 7 | CLOSED| CLOSED| CLOSED|
+----------+-------+-------+-------+
CNH1 7-8 Unit attention report mode
------------------------------------
x 7-8 CLOSED Reported
OPEN Not Reported
CNH1 9-10 SCSI bus parity check
--------------------------------
x 9-10 CLOSED Executed
OPEN Not executed
CNH1 11-12 SCSI level
----------------------
x 11-12 CLOSED SCSI-2 mode
OPEN SCSI-1 / CCS mode
CNH1 13-14 Motor start mode
----------------------------
x 13-14 CLOSED Auto start
OPEN Starting the motor is controlled with the START/
STOP command
CNH1 15-16 RESERVED
--------------------
ALWAYS CLOSED!!
CNH2 SCSI Terminating Resistor
-------------------------------
1-2 3-4
x CLOSED CLOSED From termpwr pin and IDD
CLOSED OPEN From IDD only
OPEN CLOSED From termpwr pin only
CNH2 5-6 RESERVED
------------------
ALWAYS OPEN!!
CN6 External SCSI ID connector
-------------------------------
Pin 1, 3, 5 GND
Pin 2 ID2
Pin 4 ID1
Pin 6 ID0
+----------+-----------------------+
| SCSI ID | Jumpers |
| | ID2 | ID1 | ID0 |
+----------+-------+-------+-------+
| 0 | OPEN | OPEN | OPEN |
| 1 | OPEN | OPEN | CLOSED|
| 2 | OPEN | CLOSED| OPEN |
| 3 | OPEN | CLOSED| CLOSED|
| 4 | CLOSED| OPEN | OPEN |
| 5 | CLOSED| OPEN | CLOSED|
| 6 | CLOSED| CLOSED| OPEN |
| 7 | CLOSED| CLOSED| CLOSED|
+----------+-------+-------+-------+
CN5 External LED connector
---------------------------
Pin 1 LED+
Pin 2 LED-
**********************************************************************
I N S T A L L
**********************************************************************
FUJITSU INSTALLATION CONDITIONS SCSI
Mounting in Cabinet
-------------------
Note the following points regarding mounting of the HDD in a cabinet.
If circumstances prevent the HDD from being mounted as explained
below, contact to distributers, reseller, or our sales offices.
- Mount the HDD in the specified orientation.
Mounting the HDD in an orientaion other than the specified one may
adversely affect the temperature or may cause unexpected mechanical
stress to the HDD. This may lead to a failure to guarantee the
reliability level stated in the device specifications.
- Use the specified mounting screw holes.
Mount the HDD using the mounting screw holes for each model.
If the HDD is attached by a means other than screws or with screws
but not at all specified locations (four locations), unexpected
vibration or shock may be applied to the HDD or the HDD may
mechanically resonate. This may lead to a failure to guarantee the
vibration and shock resistance levels stated in the device
specifications.
- Use mounting screws of appropriate length.
A screw shorter than appropriate length is likely to loosen, causing
the HDD to drop off the cabinet.
A screw longer than appropriate length may touch the HDD body,
causing external vibration or shock to the HDD body. This may lead to
a failure to guarantee the vibration and shock resistance levels
stated in the device specifications.
- Ensure clearance between the HDD and the cabinet.
Be sure that there is a minimum 2.5 mm clearance between the HDD and
the cabinet. Failure to do so may block ventilation and adversely
affect the operating temperature of the HDD. It may also cause the
HDD to touch the cabinet, which may then induce electrical noise or
transmit external mechanical vibration or shock directly to the HDD
body. This may result in degraded HDD performance and reliability.
Pay special attention to those models whose DE potential is not zero
volatage. If this type of model contacts the cabinet connecting the
DE to zero volatage, data errors or device faults will occur.
Grounding
---------
In an HDD with a frame, the DE and frame are electrically isolated
from each other.
The DE is connected to signal ground (SG); the frame is connected to
frame ground (FG). Isolating the DE and frame in this way prevents
the adverse effects of external electrical noise.
Generally, a computer system uses some means of connecting SG and FG
at one point in the system. The method used may vary depending on the
system structure or environmental conditions.
The DE potential in some models is not zero volatage. Be careful not
to ground the DE body of this type of model.
SCSI cable connection
---------------------
Do not confuse the connector orientation when connecting the SCSI
cable. Connecting the cable in the wrong orientation may blow the
fuse of the SCSI device that supplies power to the terminating
resistor. If the SCSI device has no fuse, misconnection may destroy
the SCSI cable.
Power-off
---------
When power is turned off, a dynamic brake stops the rotating spindle
motor. This requires a given time until the motor is completely
stopped.
Applying vibration or shock to the HDD while the spindle motor
rotates after power-off may damage the HDD.
Connecting and Disconnecting Interface Connector (2.5-inch HDD)
---------------------------------------------------------------
The printed circuit board assembly of the 2.5-inch HDD is about 0.9
mm thinner than that of conventional HDDs. When connecting or
disconnecting the interface connector, push or pull the connector
straight so as to not give excess stress to the printed circuit board
assembly. Never force a connector. Excess stress may cause the
printed circuit board assembly to warp or crack, resulting in poor
(or no) contact.
Hot Plug (SCSI Device)
----------------------
Our HDDs are designed to support the hot plug feature. However, a
drop in output voltage, output interruption, or noise may be caused
while the HDD is starting. To minimize these symptoms, it is
recommended that a discrete power supply be installed for each HDD.
Also, connection or disconnection of the HDD may cause noise on the
interface signal line and cause an interface malfunction.
To prevent such a failure, connect zero volatage (SG) first, then
connect the interface line, and finally connect the power line.
Reverse the procedure when disconnecting the HDD.
When disconnecting the HDD, do not apply vibration or shock to the
HDD, before the power is turned off. This may disturb control of the
head positioning and degrade data read-write performance.
In the worst case, applying excess shock may damage the head or disk,
resulting in data destruction.
If there is a chance that the power to the HDD containing the
terminating resistor will be turned off, design the system so that
power to the terminating resistor (TERMPWR) is supplied from another
SCSI device. Generally, TERMPWR is supplied from the initiator
(host).
**********************************************************************
G E N E R A L
**********************************************************************
FUJITSU => GDT
Tips & Hints about ICP controllers and other peripherals
========================================================
Tagged queues and Fujitsu M 26xx harddisks
------------------------------------------
Fujitsu Harddisks of the M26XX series do not support the SCSI-II
feature tagged queues. You should disable this feature in the
initialize disks menue of the GDTSetup program. An inquiry command
shows, that the harddisk supports tagged queues (this is why you can
enable it in the GDTSetup) but this is not true as stated by Fujitsu
Germany.