D K 5 1 5 - 7 8    HITACHI
NO MORE PRODUCED                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 5.25"/FH              Cylinders    1361|     |     |
Capacity form/unform   673/  780 MB        Heads          14|     |     |
Seek time   / track  16.0/ 4.0 ms          Sector/track   69|     |     |
Controller           ESDI                  Precompensation
Cache/Buffer               KB              Landing Zone
Data transfer rate    2.458 MB/S int       Bytes/Sector      512
                            MB/S ext
Recording method     RLL 2/7                        operating  | non-operating
                                                  -------------+--------------
Supply voltage     5/12 V       Temperature *C         5 45    |    -20 50
Power: sleep              W     Humidity     %         8 80    |      8 90
       standby            W     Altitude    km                 |
       idle               W     Shock        g         2       |     20
       seek               W     Rotation   RPM      3600
       read/write         W     Acoustic   dBA
       spin-up            W     ECC        Bit
                                MTBF         h     100000
                                Warranty Month
Lift/Lock/Park     YES          Certificates                                  

**********************************************************************
                        L   A   Y   O   U   T
**********************************************************************
HITACHI  DK515-78  PRODUCT MANUAL K2500279

  +----------------+      +---------------------------------+
  |                +------+                                 |XX J2
  |                +------J5                                |XX
  +--++--+         +------+                                 |XX
     ||  |                    JP213+---1                    |
     ||J4|                         8---+                    |XX
     ||  |                                             1-+  |XX
     ||  |                                        JP224| |  |XX
     |+--+                                             +-6  |XX
     |+--J6                                           +-+   |XX J1
  +--++--+                                       TM223| |   |XX
  |                                                   | |   |XX
  |                                              +J7-++-+   |XX
  |                                              +---+      |XX
  |                                                         |
  |    (SZ931 PCB REV. 0)                      +-JP281      |
  |                                          +-+-+-----1    |XX J3
  |                                         14---------JP282|XX Power
  +---------------------------------------------------------+







  +----------------+      +---------------------------------+
  |                +------+                                 |XX J2
  |                +------J5                                |XX
  +--++--+         +------+                                 |XX
     ||  |                    JP213+---1                    |
     ||J4|                         8---+                    |XX
     ||  |                                             1-+  |XX
     ||  |                                        JP224| |  |XX
     |+--+                                             +-6  |XX
     |+--J6                                           +-+   |XX J1
  +--++--+                                       TM223| |   |XX
  |                                                   | |   |XX
  |                                                   +-+   |XX
  |                                                JP281+   |XX
  |                                              +J7-++-+   |XX
  |                                              +---+      |
  | (SZ931 PCB REV. 1 OR LATER)              +---------1    |XX J3
  |                                         14---------JP282|XX Power
  +---------------------------------------------------------+



**********************************************************************
                      J   U   M   P   E   R   S
**********************************************************************
HITACHI  DK515-78  PRODUCT MANUAL K2500279

 Jumper Setting
 ==============

 JP224 Terminator Switch I
 -------------------------
 Each drive in Radial connection of cable B and last end of the drives
 in Daisy Chain connection of cable B should be terminated. Since a
 terminator module (TM223) and Terminator Switch I (JP224) are
 provided to all drives as shipped, remove both of them except the
 last drive's ones in case of Daisy Chain connection.
 +--------------------------------+------------+---------------------+
 |Configuration                   | Terminator | Terminator Switch   |
 |                                | Module     | (JP224, pins 1-6)   |
 +--------------------------------+------------+---------------------+
 |Single drive on cable B         | MOUNTED    |    6xxxx+ CLOSED 1-6|
 |All drive in Radial connection  | MOUNTED    |    +xxxx+ CLOSED 1-6|
 |The lst drive in Daisy Chain    | MOUNTED    |    +xxxx+ CLOSED 1-6|
 |                                |            |    +----1           |
 +--------------------------------+------------+---------------------+
 |All drives except the last one  | REMOVED    |    6----+ OPEN 1-6  |
 |in Daisy Chain                  |            |    +----+           |
 |                                |            |    +----+           |
 |                                |            |    +----1           |
 +--------------------------------+------------+---------------------+
 At the time of shipment, Terminator Module and Terminator Switch I
 are mounted on Terminator socket.


 Synchronized Spindle Signal Terminator Switch II JP281
 ------------------------------------------------------
 Synchronized Spindle Signal is terminated via JP281 to terminator
 register on the PCB. When the synchronized spindle option is used,
 JP281 shall be removed except the last drive's one in Daisy Chain of
 Synchronized Spindle Signal.

 JP281 CLOSED  The last Slave drive
       OPEN    All drives except the last Slave drive

 A drive as shipped is mounted with Terminator Switch II.


 JP213 Pin 1-6  Drive Address
 ----------------------------
 +--------------+-----+-------------------------------------------+
 | Setting      |Drive|   Pins                                    |
 |              | No.#|                                           |
 +--------------+-----+-------------------------------------------+
 | 7--+--+--+--1|     |                                           |
 | |  |  |  |  || None|NOT USED!                                  |
 | 8--+--+--+--2|     |                                           |
 +--------------+-----+-------------------------------------------+
 | 7--+--+--+--1|     |                                           |
 | |  |  |  |XX||  1  |install the jumper plug for JP213 1,2      |
 | 8--+--+--+--2|     |                                           |
 +--------------+-----+-------------------------------------------+
 | 7--+--+--+--1|     |                                           |
 | |  |  |XX|  ||  2  |install the jumper plug for JP213 3,4      |
 | 8--+--+--+--2|     |                                           |
 +--------------+-----+-------------------------------------------+
 | 7--+--+--+--1|     |                                           |
 | |  |  |XX|XX||  3  |install the jumper plugs for JP213 1 4     |
 | 8--+--+--+--2|     |                                           |
 +--------------+-----+-------------------------------------------+
 | 7--+--+--+--1|     |                                           |
 | |  |XX|  |  ||  4  |install the jumper plug for JP213 5,6      |
 | 8--+--+--+--2|     |                                           |
 +--------------+-----+-------------------------------------------+
 | 7--+--+--+--1|     |                                           |
 | |  |XX|  |XX||  5  |install the jumper plugs for JP213 1,2,5,6 |
 | 8--+--+--+--2|     |                                           |
 +--------------+-----+-------------------------------------------+
 | 7--+--+--+--1|     |                                           |
 | |  |XX|XX|  ||  6  |install the jumper plugs for JP213 3 6     |
 | 8--+--+--+--2|     |                                           |
 +--------------+-----+-------------------------------------------+
 | 7--+--+--+--1|     |                                           |
 | |  |XX|XX|XX||  7  |install the jumper plugs for JP213 1 6     |
 | 8--+--+--+--2|     |                                           |
 +--------------+-----+-------------------------------------------+
 At the time of shipment, Drive #1 is selected.


 JP213 7-8  Write Protect Jumper
 -------------------------------
 Write operation of a drive is inhibited by setting a jumper on JP213,
 pin 7-8 (Write Protect mode), which condition will generate ATTENTION
 status upon receiving of WRITE GATE-N signal.

 JP213 7-8 CLOSED  Write Protect
           OPEN    Write Enable

 At the time of shipment, "Write Enable" mode is selected.


 JP282 1-2  Sector Mode Select
 -----------------------------
 JP282 1-2 CLOSED  Hard Sector
           OPEN    Soft Sector

 The drive with Hard Sector mode issues clock on J1-pin 16 and J2-pin
 2. "SET CONFIGURATION" command takes precedence over this Jumper
 setting function.

 At the time of shipment, "Hard Sector" mode is selected.


 JP282 7-8  Motor Control Jumper
 -------------------------------
 When the "Start/Stop Spindle Motor" option is to be used, set the
 jumper as "Supported" before DC power on.

 JP282 7-8  CLOSED  Not Supported (Factory Setting)
            OPEN    Supported


 JP282 3-6 Synchronized Spindle Mode Select Jumper
 -------------------------------------------------
 Synchronized spindle mode can be selected by using the jumper switch
 (JP282, pin 3-6). This Jumper Setting will be aborted by the follow-
 ing Set Configuration command. Set tge jumpers, before turning on the
 DC power.

 pin 3-4 and 5-6 CLOSED  Off Line (Factory setting)
             5-6 CLOSED  Slave  (3-4 OPEN)
             3-4 CLOSED  Master (5-6 OPEN)
     3-4 and 5-6 OPEN    Remote


 JP282 9-14 Sector Length Jumper
 -------------------------------

  14---13          14---13           14---13           14---13
   |XXX|            |XXX|             |XXX|             |XXX|
   +---+            +---+             +---+             +---+
   |XXX|            |XXX|             |   |             |   |
   +---+            +---+             +---+             +---+
   |XXX|            |   |             |XXX|             |   |
 10+---+9         10+---+9          10+---+9          10+---+9
   |                |                 |                 |
 335 Bytes/Sec.   338 Bytes/Sec.     593 Bytes/Sec.   602 Bytes/Sec.
 122 Sec/track    121 Sec/track       69 Sec/track     68 Sec/track
 256 Data Length  256 Data Length    512 Data Length  512 Data Length
 (Factory Setting)

  14---13          14---13           14---13           14---13
   |   |            |   |             |   |             |   |
   +---+            +---+             +---+             +---+
   |XXX|            |XXX|             |   |             |   |
   +---+            +---+             +---+             +---+
   |XXX|            |   |             |XXX|             |   |
 10+---+9         10+---+9          10+---+9          10+---+9
   |                |                 |                 |
 Adjustment Mode  1107 Bytes/Sec.    NOT USED         NOT USED
                    37 Sec/track
                  1024 Data Length