8 2 1 0 0 A 4 C R Y S T A L 1 0 8 0 MAXTOR
Native| Translation
------+-----+-----+-----
Form 3.5"/SLIMLINE Cylinders | 4092| |
Capacity form/unform 2100/ MB Heads 4| 16| |
Seek time / track 11.0/ 2.0 ms Sector/track | 63| |
Controller IDE / ATA2 FAST/ENHA Precompensation
Cache/Buffer 256 KB Landing Zone
Data transfer rate 8.000 MB/S int Bytes/Sector 512
16.700 MB/S ext PIO4
Recording method RLL 8/9 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 5 55 | -40 71
Power: sleep 0.9 W Humidity % 5 95 | 5 95
standby 1.3 W Altitude km -0.061 3.048| -0.061 12.192
idle 4.0 W Shock g 20 | 200
seek 4.8 W Rotation RPM 4480
read/write 4.8 W Acoustic dBA 36
spin-up 13.7 W ECC Bit
MTBF h 400000
Warranty Month
Lift/Lock/Park YES Certificates
**********************************************************************
L A Y O U T
**********************************************************************
MAXTOR 84320/83201/82580/82100/81620/81081A JUMPER SETTING
Pin 1
J1 IDE Connector | J2 Power
+----------- --------+-++-----------+---------+
| .................... || @ * * o | |
| .......... ......... || @ o o o o | O O O O |
+----------------------++-----------+---------+
| | | | | | | | |
| | | | | | | | |
J50 Master/Slave ---+ | | | | | | | +- +12V (Yellow)
J48 Cable Select -----+ | | | | | +--- +12V Return (Black)
J46 4092 Cyl Limitation + | | | +----- +5V Return (Black)
J44 Factory Reserved -----+ | +------- +5V (Red)
J42 Factory Reserved -------+
@ = Default Jumped Positions
* = "Spare" Jumper Position
o = Default Open Positions
**********************************************************************
J U M P E R S
**********************************************************************
MAXTOR 84320/83201/82580/82100/81620/81081 JUMPER SETTING
Jumper Setting
==============
Jumper Designations |J50|J48|J46|J44|J42|
+-------------------------------------+---+---+---+---+---+
| Master/Slave | | | | | |
| Only Drive in single drive system* | J | | | | |
| Master in a dual drive system* | J | | | | |
| Slave in a dual drive system | O | | | | |
+-------------------------------------+---+---+---+---+---+
| Cable Select | | | | | |
| Disabled* | | O | | | |
| Enabled | | J | | | |
+-------------------------------------+---+---+---+---+---+
| 4092 Cylinder Option | | | | | |
| Disabled* | | | O | | |
| Enabled | | | J | | |
+-------------------------------------+---+---+---+---+---+
| Factory Reserved | | | | O | |
+-------------------------------------+---+---+---+---+---+
| Factory Reserved | | | | | |
+-------------------------------------+---+---+---+---+---+
J=Jumpered O=Open *=Default
Systems Using Cable Select
--------------------------
Most systems do not use this feature. Unless you are sure that the
system that the Maxtor hard drive is being installed in uses Cables
Select, do not set up the drive with this feature enabled.
Maxtor hard drives support Cable Select - which allows the system
to identify Devuce 0 and Device 1 drives on the interface cable. If
your system manufacturer for specific procedures for installing hard
drives.
On Maxtor CrystalMax hard drives, the Cable Select is enabled by
installing a jumper on J48. When J48 is installed, remove the jumper
from J50.
WARNING
Do NOT install Cable Select jumper unless you are sure that the
system requires this feature. The drive will not operate correctly in
systems which do not support Cable Select.
System Hangs During Boot
------------------------
If the system hangs after installing the Maxtor hard drive, either
before or after setting the system BIOS, the system may have a BIOS
with a cylinder limitation. This may occur for hard drives with
capacities larger than 2.1GB. If this happens, do the following:
1. Turn the system OFF.
2. Install the cylinder reduction jumper (J46) on the drive using the
spare jumper across pins J46 and J48; or, if the drive is
installed as a Slave, store the spare jumper across J42 and J44.
3. If the BIOS was set to AUTO DETECT, boot the system with the MAX
BLAST installation software diskette to complete the hard drive
installation. If other BIOS setting were used, access the BIOS
SETUP program and set the BIOS parameters to a Type 9 for the
Maxtor hard drive. Then boot the system with the MAXBLAST
installation software diskette to complete the hard drive
installation.
NOTE
When this jumper is installed, the Maxtor hard drive must be
prepared using the MAXBLAST installation software.