L X T - 5 0 S MAXTOR
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 3.5"/HH Cylinders 733| | |
Capacity form/unform 48/ MB Heads 4| | |
Seek time / track 27.0/ ms Sector/track 32| | |
Controller SCSI1 SINGLE-ENDED Precompensation 65535
Cache/Buffer KB Landing Zone 732
Data transfer rate 1.250 MB/S int Bytes/Sector 512
MB/S ext
Recording method operating | non-operating
-------------+--------------
Supply voltage Temperature *C |
Power: sleep W Humidity % |
standby W Altitude km |
idle W Shock g |
seek W Rotation RPM
read/write W Acoustic dBA
spin-up W ECC Bit
MTBF h 40000
Warranty Month 12
Lift/Lock/Park YES Certificates
**********************************************************************
L A Y O U T
**********************************************************************
MAXTOR LXT-50S PRODUCT DESCRIPTION
+---------------------------------------------------------+
| |XX I
| |XX N
| |XX T
| |XX E
| |XX R
| |XX F
| |XX A
| |XX C
| |XX E
| |XX
| |+-1
| || |
| || |J1
| |+-+
| 1 |
| XXXXXXPower
+---------------------------------------------------------+
**********************************************************************
J U M P E R S
**********************************************************************
MAXTOR LXT-50S PRODUCT DESCRIPTION
Jumper Setting
==============
J1 Pins 1-2 Parity checking
----------------------------
1-2 CLOSED Parity checking enabled
OPEN Parity checking disabled
J1 SCSI ID
-----------
+----------+-----------------------+
| SCSI ID | Jumpers |
| | 7-8 | 5-6 | 3-4 |
+----------+-------+-------+-------+
| 0 | OPEN | OPEN | OPEN |
| 1 | OPEN | OPEN | CLOSED|
| 2 | OPEN | CLOSED| OPEN |
| 3 | OPEN | CLOSED| CLOSED|
| 4 | CLOSED| OPEN | OPEN |
| 5 | CLOSED| OPEN | CLOSED|
| 6 | CLOSED| CLOSED| OPEN |
| 7 | CLOSED| CLOSED| CLOSED|
+----------+-------+-------+-------+
**********************************************************************
G E N E R A L
**********************************************************************
MAXTOR SCSI INSTALLATION
GENERIC INSTALLATION PROCEDURE FOR A SCSI DRIVE
-----------------------------------------------------------
1. Install a 50 pin ribbon connector making sure pin 1, which
can be identified by the striped edge of the cable, is closest
to the power connector on the drive.
2. Install a DC power cable to the back of the drive.
3. Verify the SCSI ID selection.
Note: SCSI ID usually needs to be set to 0 to be the boot drive.
The last physical device on the SCSI bus must be terminated.
Any other drive or SCSI device connected between the host and
the device at the end of the bus must not be terminated.
4. Apply power to the computer.
4a. When memory test is complete go into your system's Standard
C-MOS set-up.
(Note: There are various ways to get into C-MOS set-up,
please refer to system's manual for instuctions.)
4b. Set the drive type to "Not Installed". This intelligent drive
will identify itself to the SCSI host adapter.
5. Boot from a DOS diskette that has FDISK.EXE and FORMAT.COM on
it. At the A> prompt type in FDISK. At the menu options select
option 1 to create a DOS partition. Another menu will appear and
from those options choose 1 to create a Primary DOS partition.
Select yes to make 1 large partition and it will automatically
become active. Then escape from FDISK.
6. At the A> prompt type in FORMAT C:/S
This does a high-level format on the drive and transfers the
system files in order for the drive to be bootable.
(Note: Maxtor SCSI drives are low-level formatted at the factory)
7. The drive is now bootable. As a test remove the DOS diskette
from A and press reset to re-boot the computer, a C> should be
displayed, the drive is now ready for operation.