9 0 8 4 5 D 5 D I A M O N D M A X MAXTOR
Native| Translation
------+-----+-----+-----
Form 3.5"/SLIMLINE Cylinders | | |
Capacity form/unform 8455/ MB Heads 5| | |
Seek time / track 9.0/ 0.9 ms Sector/track | | |
Controller IDE / ATA4 ULTRA Precompensation
Cache/Buffer 256 KB SDRAM Landing Zone
Data transfer rate 18.600 MB/S int Bytes/Sector 512
33.000 MB/S ext
Recording method operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 5 55 | -40 71
Power: sleep W Humidity % 5 95 | 5 95
standby 0.9 W Altitude km -0.061 3.048| -0.061 12.192
idle 4.4 W Shock g 20 | 200
seek 9.6 W Rotation RPM 5400
read/write 4.8 W Acoustic dBA 36
spin-up 20.2 W ECC Bit
MTBF h 500000
Warranty Month 36
Lift/Lock/Park YES Certificates
**********************************************************************
L A Y O U T
**********************************************************************
MAXTOR DIAMOND MAX 3400
Pin 1
J1 IDE Connector | J2 Power
+----------- --------+-++-----------++---------+
| .................... || @ * * * || X X X X |
| .......... ......... || @ * * * * || X X X X |
+----------------------++-+-+-+-+-+-++-+-+-+-+-+
| | | | | | | | |
| | | | | | | | |
J50 Master/Slave -----+ | | | | | | | +-+12V
J48 Cable Select -------+ | | | | | +---+12V Return
J46 4092 Cyl Limitation---+ | | | +----- +5V Return
J44 Factory Reserved -------+ | +------- +5V
J42 Factory Reserved ---------+
**********************************************************************
J U M P E R S
**********************************************************************
MAXTOR DIAMOND MAX INSTALLATION SHEET
Jumper Setting
==============
+---+---+---+---+---+
|J50|J48|J46|J44|J42|
+-------------------------------------+---+---+---+---+---+
| Master/Slave | | | | | |
| Only Drive in single drive system* | J | | | | |
+-------------------------------------+---+---+---+---+---+
| Master in a dual drive system* | J | | | | |
+-------------------------------------+---+---+---+---+---+
| Slave in a dual drive system | O | | | | |
+-------------------------------------+---+---+---+---+---+
| Cable Select | | | | | |
| Disabled* | | O | | | |
+-------------------------------------+---+---+---+---+---+
| Enabled | | J | | | |
+-------------------------------------+---+---+---+---+---+
J=Jumpered O=Open *=Default
**********************************************************************
I N S T A L L
**********************************************************************
MAXTOR 91360D8/91190D7/91020D6/90845D5/90680D4/90510D3/90340D2
Notes on installation
=====================
Installation direction
----------------------
horizontally vertically
+-----------------+ +--+ +--+
| | | +-----+ +-----+ |
| | | | | | | |
+-+-----------------+-+ | | | | | |
+---------------------+ | | | | | |
| | | | | |
| | | | | |
+---------------------+ | +-----+ +-----+ |
+-+-----------------+-+ +--+ +--+
| |
| |
+-----------------+
The drive will operate in all axis (6 directions).
Idle
The drive is spinning., the actuator is parked and powered
off, and all other circuitry is powered on. The drive is
capable of responding to read commands within 40 ms.
Read/Write
Data is being read from or written to the drive.
Spin-up
The drive is spinning up following initial application
of power and has yet not reached full speed. Maximum
current draw lasts one second.
Standby
The spin motor is not spinning. The drive will leave this
mode upon receipt of a command that requires disk access.
The time-out value for this mode is programmable. The
buffer is active to accept write data.
Sleep
This is the lowest power state - with the interface set to
inactive. A software or hardware reset is required to return
the drive to the standby state.
**********************************************************************
G E N E R A L
**********************************************************************
MAXTOR IDE INSTALLATION
INSTALLATION PROCEDURE FOR AN IDE DRIVE
---------------------------------------
1. Install a 40 pin Data Cable ensuring that pin 1, which can be
identified by the striped edge of the cable, is closest to the
power connector on the drive.
2. Install a DC power cable to the back of the drive.
3. Verify the jumper configurations for Master/Slave operation
(Note: Master will be the bootable drive. The slave will not
be bootable.) Also make sure the existing C: drive is jumped
to be the Master in a two drive system, not the only drive in
the system.
4. Apply power to the computer.
4a. When memory test is complete go into your system's Standard
CMOS set-up.
(Note: There are various ways to get into CMOS set-up, please
refer to system's manual for instructions.)
4b. If your system's BIOS supports a user programmable drive
type, program the BIOS with the default parameters of your
drive. If your system does not support a user programmable
drive type choose parameters that closely match but do not
exceed the drives MegaByte capacity. Escape from set-up
then choose write to CMOS and exit.
5. Boot from a DOS diskette that has FDISK.EXE and FORMAT.COM on
it. At the A> prompt type in FDISK. At the menu options select
option 1 to create a DOS partition. Another menu will appear
and from those options choose 1 to create a Primary DOS
partition. Select yes to make 1 large partition and it will
automatically become active. Then escape from FDISK.
6. At the A> prompt type in FORMAT C:/S This does a high-level
format on the drive and transfers the system files in order for
the drive to be bootable. (Note: IDE drives are low-level
formatted from the manufacturer and only need a high-level
format).
To configure the drive as a slave drive repeat steps 1-4 and
proceed with steps 5a. and 6a. as follows:
5a. At the C> prompt type in FDISK. When the menu options appear
select option 5 to switch to the second drive. Enter fixed
disk drive number 2. Then choose option 1 to create a DOS
partition, then select option 1 again to create a Primary DOS
partition or option 2 to create an Extended DOS partition.
(Note: C and D drives will always be the Primary partitions
but only the Primary partition on C: will have a status of
active).
6a. Proceed with a high-level format on the drive by typing FORMAT
D: (Note: Make sure the correct drive letter has been selected
for format).
7. The drive is now bootable. As a test remove the DOS diskette
from A and press reset to reboot the computer, a C> should be
displayed, the drive is now ready for operation.