M 1 6 3 6 T A U P I C O B I R D 9 FUJITSU
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 3.5"/SLIMLINE Cylinders 6189| 2490| |
Capacity form/unform 1284/ MB Heads 2| 16| |
Seek time / track 11.0/ 3.0 ms Sector/track | 63| |
Controller IDE / ATA2 FAST/ENHA Precompensation
Cache/Buffer 128 KB FIFO BUFFER Landing Zone
Data transfer rate 7.700 MB/S int Bytes/Sector 512
16.700 MB/S ext PIO4
Recording method PRML 8/9 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 5 55 | -40 60
Power: sleep 1.1 W Humidity % 8 80 | 5 95
standby W Altitude km -0.300 3.000| -0.300 12.000
idle W Shock g 5 | 75
seek W Rotation RPM 5400
read/write W Acoustic dBA 35
spin-up W ECC Bit SMART
MTBF h 500000
Warranty Month
Lift/Lock/Park YES Certificates
**********************************************************************
L A Y O U T
**********************************************************************
FUJITSU M163X/162XTAU JUMPER SETTING
Jumper
+Power-----2-6----------------------+
|xxxxxxxx ooo ooooooooo oooooooooo |
|XXXXXXXX ooo oooooooooooooooooooo |
|1 1 5 |
+---------------Interface-----------+
**********************************************************************
J U M P E R S
**********************************************************************
FUJITSU M163X/162XTAU JUMPER SETTING
Jumper Setting
==============
2 6
X o o
X o o MASTER (default)
1 5
2 6
o X o
o X o SLAVE
1 5
2 6
xxx o
o o o CABLE SELECT Cable Select Mode gives an alternative method
1 5 by which the drive may be set to MASTER or
SLAVE. A special cable is needed to implement
this feature and ahould only be used by BOTH
drives.
**********************************************************************
I N S T A L L
**********************************************************************
FUJITSU M163X/162XTAU JUMPER SETTING
Notes On Installation
=====================
Grounding
---------
Sufficient grounding will be provided for correct operation when
the drive is screwed into an electrically grounded frame.
Orientation
-----------
The drive may be installed in one of three orientations; PCA down
or on either edge.
horizontally vertically
+-----------------+ +--+ +--+ +------------------+
| | | +-----+ +-----+ | | | x
| | | | | | | | x+----------------+x
+-+-----------------+-+ | | | | | | ||x x||
+---------------------+ | | | | | | || x x ||
| | | | | | || x x ||
x x | | | | | | || x x ||
+------x------x-------+ | +-----+ +-----+ | || xx ||
+-+------x--x-------+-+ +--+ +--+ || x x ||
| xx | || x x ||
| x x | || x x ||
+---x--------x----+ |x x|
x x x++----------------++x
UNACCEPTABLE! UNACCEPTABLE!
Never install PC board on the Top!
Cooling
-------
Allow space above and below the drive to provide for adequate air
flow. Fan cooling is recommended. The disk enclosure temperature,
measured at top center, should never exceed 60*C.
Mounting screw fixing
---------------------
When the mounting screw holes on the side of the drive are used, then
use only the two pairs of outer holes. Do not use the center hole in
conjunction with only one of the outer holes. The screw must not
penetrate the drive.
Screws: 6-32UNC